L2Pass NFT Mint & Bridge

Setting up and getting up and running pint and NFT sending wallets via the L2Pass protocol.

PreviousMerkly NFT Mint & Bridge NextRescue mode

Last updated 10 months ago

L2Pass NFT Mint & Bridge

Setting up and getting up and running pint and NFT sending wallets via the L2Pass protocol.

The L2Pass NFT Mint & Bridge mode allows you to mint and send NFTs to other networks through the L2Pass protocol.

The NFT minting is done on the ZkEVM network, with the possibility to send the minted NFT to any of the 16 available networks.

Setting up and starting a session:

In the Mode section, select Block Mode.
In the Run mode section, choose the order in which wallets will be launched:
1. Parallel - parallel operation (multithreaded) with or without proxies.
2. One-by-one - wallets will be launched one after another with or without proxies.
3. One-by-one (mobile proxy) - wallets will be launched one after another using mobile proxies. Mobile proxies must be added in Settings -> and linked to accounts in beforehand.
To use a ready-made software settings preset, click the selection field in the Select preset section and choose the desired preset.
To launch a pre-prepared group of wallets, select the desired one in the Select Accounts group to launch section.
In the Bridge NFT After Mint to field, select the network to which the NFT will be sent after minting.
In the Delays section, set the delay between wallets in the Wallet field.
By clicking Pro, you will open the Gas guard settings. When this delay is activated, your wallet will go into sleep mode if several accounts in the same session are simultaneously ready to work after reaching the gas level set by you for the software operation. This is done to prevent all these wallets from simultaneously sending transactions after reaching the gas level you set. The standard delay is set between 30 to 150 seconds.
In the Max gas price section, set the maximum gas in the Ethereum network at which transactions will be made. The software will wait until the gas in the Ethereum network drops to the required level and will only start making transactions then. After the session starts, you can change the upper Gwei level in the Logs & Progress tab by going to the Sessions subsection.
If you want the wallets to work in random order, leave the Randomize wallets checkbox checked.
To save the session delay settings for use in other sessions, click the Save this as preset button, enter the preset name, and save. Later, this preset can be selected in the Select preset field.
Click Update Balances to get the actual ETH balances on the wallets.
Select the wallets you want to launch and click Launch.

PreviousMerkly NFT Mint & Bridge NextRescue mode

Last updated 10 months ago

The L2Pass NFT Mint & Bridge mode allows you to mint and send NFTs to other networks through the L2Pass protocol.

The NFT minting is done on the ZkEVM network, with the possibility to send the minted NFT to any of the 16 available networks.

Setting up and starting a session:

In the Mode section, select Block Mode.
In the Run mode section, choose the order in which wallets will be launched:
1. Parallel - parallel operation (multithreaded) with or without proxies.
2. One-by-one - wallets will be launched one after another with or without proxies.
3. One-by-one (mobile proxy) - wallets will be launched one after another using mobile proxies. Mobile proxies must be added in Settings -> and linked to accounts in beforehand.
To use a ready-made software settings preset, click the selection field in the Select preset section and choose the desired preset.
To launch a pre-prepared group of wallets, select the desired one in the Select Accounts group to launch section.
In the Bridge NFT After Mint to field, select the network to which the NFT will be sent after minting.
In the Delays section, set the delay between wallets in the Wallet field.
By clicking Pro, you will open the Gas guard settings. When this delay is activated, your wallet will go into sleep mode if several accounts in the same session are simultaneously ready to work after reaching the gas level set by you for the software operation. This is done to prevent all these wallets from simultaneously sending transactions after reaching the gas level you set. The standard delay is set between 30 to 150 seconds.
In the Max gas price section, set the maximum gas in the Ethereum network at which transactions will be made. The software will wait until the gas in the Ethereum network drops to the required level and will only start making transactions then. After the session starts, you can change the upper Gwei level in the Logs & Progress tab by going to the Sessions subsection.
If you want the wallets to work in random order, leave the Randomize wallets checkbox checked.
To save the session delay settings for use in other sessions, click the Save this as preset button, enter the preset name, and save. Later, this preset can be selected in the Select preset field.
Click Update Balances to get the actual ETH balances on the wallets.
Select the wallets you want to launch and click Launch.

Your wallets have been launched. You can track the process of work of your wallets in the section .