Merkly NFT Mint & Bridge

Set up and put into operation wallets for minting and sending NFTs via the Merkly protocol.

PreviousDeploy Contracts NextL2Pass NFT Mint & Bridge

Last updated 10 months ago

Merkly NFT Mint & Bridge

Set up and put into operation wallets for minting and sending NFTs via the Merkly protocol.

The Merkly NFT Mint & Bridge mode allows you to and send NFTs to other networks via the Merkly protocol.

Minting of NFTs is done on the ZkEVM network with the ability to send the minted NFT to any of the 20 available networks.

Setting up and starting a session:

In the Mode section, select Block Mode.
In the Run mode section, choose how the wallets will be launched:
- Parallel - parallel operation (multi-threading) with or without proxies.
- One-by-one - wallets will be launched one after another with or without proxies.
- One-by-one (mobile proxy) - wallets will be launched one after another using mobile proxies. Mobile proxies should be added in the Settings -> section and linked to accounts in the .
To use a preset configuration for the software, click the selection field in the Select preset section and choose the desired preset.
To launch a pre-prepared group of wallets, select the desired group in the Select Accounts group to launch section.
In the Bridge NFT After Mint to field, select the network to which the NFT will be sent after minting.
In the Delays section, set the delay between wallet launches in the Wallet field.
Clicking on Pro will open the Gas guard setting. If this delay is activated, your wallet will go to sleep if multiple accounts in the same session are ready to work simultaneously after reaching the gas level you set for the software. This is to prevent all these wallets from sending transactions at the same time after reaching your specified gas level. The standard delay is set between 30 and 150 seconds.
In the Max gas price section, set the maximum gas in the Ethereum network at which transactions will be made. The software will wait until the gas in the Ethereum network drops to the specified value and will only then start making transactions. After starting the session, you can change the upper Gwei level in the Logs & Progress tab, in the Sessions subsection.
If you want wallets to start working in random order, leave the Randomize wallets checkbox enabled.
To save the session delay settings for use in other sessions, click the Save this as preset button.
Click Update Balances to get the current ETH balances on the wallets.
Select the wallets you want to start working and click Launch.

PreviousDeploy Contracts NextL2Pass NFT Mint & Bridge

Last updated 10 months ago

The Merkly NFT Mint & Bridge mode allows you to and send NFTs to other networks via the Merkly protocol.

Minting of NFTs is done on the ZkEVM network with the ability to send the minted NFT to any of the 20 available networks.

Setting up and starting a session:

In the Mode section, select Block Mode.
In the Run mode section, choose how the wallets will be launched:
- Parallel - parallel operation (multi-threading) with or without proxies.
- One-by-one - wallets will be launched one after another with or without proxies.
- One-by-one (mobile proxy) - wallets will be launched one after another using mobile proxies. Mobile proxies should be added in the Settings -> section and linked to accounts in the .
To use a preset configuration for the software, click the selection field in the Select preset section and choose the desired preset.
To launch a pre-prepared group of wallets, select the desired group in the Select Accounts group to launch section.
In the Bridge NFT After Mint to field, select the network to which the NFT will be sent after minting.
In the Delays section, set the delay between wallet launches in the Wallet field.
Clicking on Pro will open the Gas guard setting. If this delay is activated, your wallet will go to sleep if multiple accounts in the same session are ready to work simultaneously after reaching the gas level you set for the software. This is to prevent all these wallets from sending transactions at the same time after reaching your specified gas level. The standard delay is set between 30 and 150 seconds.
In the Max gas price section, set the maximum gas in the Ethereum network at which transactions will be made. The software will wait until the gas in the Ethereum network drops to the specified value and will only then start making transactions. After starting the session, you can change the upper Gwei level in the Logs & Progress tab, in the Sessions subsection.
If you want wallets to start working in random order, leave the Randomize wallets checkbox enabled.
To save the session delay settings for use in other sessions, click the Save this as preset button.
Click Update Balances to get the current ETH balances on the wallets.
Select the wallets you want to start working and click Launch.

Your wallets have been launched. You can track the process of work of your wallets in the section .