---
description: Set up and run sessions to send tokens from one network to another.
---

# Bridge mode

Thanks to the Bridge mode, you can replenish wallet balances with native tokens for further activity in the desired network. Bridge mode allows bridging tokens from any available network to another, without being tied to the module's network.

* In the **Mode** section, select **Bridge Mode**;
* In the **Run** mode section, choose how wallets will be launched:
  1. **Parallel**: wallets will operate concurrently (multithreaded) with or without proxies;
  2. **One-by-one**: wallets will be launched one after another with or without proxies;
  3. **One-by-one (mobile proxy)**: wallets will be launched one after another using mobile proxies. Mobile proxies must first be added to the **Settings** -> [**Proxies**](https://docs.nfd.gg/main/eng-combine-software/section-settings/proxies) section and linked to accounts in the [Account Manager](https://docs.nfd.gg/main/eng-combine-software/account-manager).
* **To launch** a pre-prepared group of wallets, select the desired one in the **Select Accounts group to launch** section;
* In the **Bridge Type** section, choose the bridge through which you want to send tokens. All modules have several bridges to choose from: official bridges and third-party developer bridges;
* If you want to send funds through an official bridge, select it from the list and proceed to the settings. Almost all official bridges only work with the Ethereum network. Therefore, to send ETH to the L2 network via official bridges, you must have ETH on your Ethereum balance;
* In the **Account Delays** section, set the delay between wallet launches in seconds;
* When you click on **Pro**, the **Gas guard** setting will open. If this delay is activated, your wallet will additionally go to sleep if several accounts in the same session are ready to work simultaneously after reaching the gas level you set for the software. This is done so that all these wallets do not start sending transactions simultaneously after reaching the set gas level. The standard delay range is from 30 to 150 seconds;
* If you are using a third-party bridge or an official bridge that allows you to choose networks other than Ethereum, then in the **Chain from and to** field, select the network from which the tokens will be sent in the first window and the network to which the tokens will be sent in the second window.
* Below the network selection fields, there are two informational banners: **Min amount** displays the minimum amount to be sent and **Trading fee** displays the bridge fee excluding gas fees;
* Click **Update Balances** to see the current balance on the wallets. If your wallet balances in the Zora network are not loading, you should understand that Zora adheres to sanctions and all countries that are on the OFAC list are banned by Zora. You need to enable VPN before updating balances so that they are updated;
* Select the wallets you want to use in the session;
* In the **Amount** section, there are three functions: **All**, **Send range**, and **Leave range** if you use the official bridge, and two functions **Send range** and **Leave range** if you use a third-party bridge;
  1. **All** - will transfer all available tokens on the wallet to the destination network;
  2. **Send range** - allows you to send tokens within a specified range;
  3. **Leave range** - allows you to leave a specified range of tokens on the wallets and send only what is above this range.
* Enter the amount range in the required fields and click **Apply to selected wallets**. The amount for each wallet will be generated randomly within the specified range for each wallet. The amount that will be applied to the wallet can be seen in the **Amount to bridge** field. You can also manually change the amount in this field;
* In the **Max gas price** section, set the maximum gas in the Ethereum network at which transactions will be executed. The software will wait for the gas to drop to the required level and will start transactions when the gas drops to the level you specified. After the session starts, you can change the upper Gwei level in the **Logs & Progress** tab by going to the **Sessions** subsection;
* To make wallets work in random order, keep the **Randomize wallets** checkbox enabled;
* To start the wallets, click **Launch**.

<figure><img src="https://883793412-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FwkJ3XgG3awYBhDsxkXtj%2Fuploads%2FAEkiqE0JLpXpGuK3IqmR%2FCo4232mbine.gif?alt=media&#x26;token=e28dc5c5-4f27-4319-a79a-969970c012fd" alt=""><figcaption></figcaption></figure>

* Your wallets have been launched. You can track the process of work of your wallets in the section [Logs & Progress](https://docs.nfd.gg/main/eng-combine-software/modules/operation-and-launching-of-modules/zora-module/logs-and-progress).
